Fujitsu 97.3 error code

What it means

Fujitsu's outdoor board shows these dot-decimal codes only after an error is active: the red ERROR LED blinks at high speed, then a brief SW1 press makes the MONITOR LEDs blink out the code. Code 97.3 means the outdoor unit is not controlling the compressor motor normally. Repeated resets can stress the compressor and inverter.

Urgency

Likely causes

1. Brief power event, brownout, or unstable supply voltage
2. Loose power connection, reactor, or outdoor electrical component problem
3. Inverter/IPM protection or current-detection fault
4. Compressor winding, drive, or outdoor board fault after power checks pass

Homeowner fix

Turn the system off and reset once if safe. If the code returns, leave the system off and do not force repeated compressor starts.

When to call a pro

Call a licensed HVAC technician if the code returns or the outdoor unit will not start. Tell them the exact Fujitsu SW1 code is 97.3 and the Section 14-3 meaning is: Compressor motor control error.

Repair vs replace

Compressor and inverter findings can be expensive. If the system is older or out of warranty, compare a confirmed compressor, inverter, or outdoor-board quote with replacement.

• Fujitsu AIRSTAGE H-series Compact Cassette 9,000 BTU R-32 208/230V (ACUH09KUAS / AOUH09KUAS1)

  AIRSTAGE H-series

• Fujitsu AIRSTAGE H-series Compact Cassette 12,000 BTU R-32 208/230V (ACUH12KUAS / AOUH12KUBS1)

  AIRSTAGE H-series

• Fujitsu AIRSTAGE H-series Floor-Mounted Console 12,000 BTU R-32 208/230V (AGUH12KUAS / AOUH12KUBS1)

  AIRSTAGE H-series

• Fujitsu AIRSTAGE H-series Mid Static Duct 12,000 BTU R-32 208/230V (ARUH12KUAS / AOUH12KUBS1)

  AIRSTAGE H-series

Parts for this line

The parts catalog for Fujitsu AIRSTAGE H-series lists 6 sourced replacement parts for this product line.

For your technician

Technician note: Section 14-3 lists 97.3 as Compressor motor control error; check compressor terminals, wiring order, winding resistance, insulation, drive output, IPM/inverter, setup data, and outdoor PCB. Page context: Fujitsu maps this display to the AIRSTAGE H-series line; source: Fujitsu AOUH18-45KWAS/KWAH R-32 Design & Technical Manual; display convention: match the ninety seven and three marker exactly before comparing neighboring codes.

Which systems show it

• Fujitsu Halcyon/AIRSTAGE R-32 AOUH18KWAS2, AOUH24KWAS3, AOUH36KWAS4, and AOUH45KWAS5 outdoor-unit manuals where Section 14-3 lists the same SW1/MONITOR error-code table.
• Fujitsu AOUH18KWAH2 and AOUH36KWAH4 XLTH sibling design manuals where the extracted Section 14-3 table matches the KWAS manuals.

Related troubleshooting

Use the symptom guide alongside the exact display code if the unit is flashing, cycling, or showing comfort symptoms.

Reset note

Turn the system off and reset once if safe. If the code returns, leave the system off and do not force repeated compressor starts.

Manual trigger

Fujitsu's outdoor board shows these dot-decimal codes only after an error is active: the red ERROR LED blinks at high speed, then a brief SW1 press makes the MONITOR LEDs blink out the code. Code 97.3 means the outdoor unit is not controlling the compressor motor normally. Repeated resets can stress the compressor and inverter.

Related codes

Source

Next step